|
HFStuart
|
 |
« on: June 11, 2014, 12:55:21 PM » |
|
Does anyone know when they switched the screen on the Spider from bonded type to rubber sealed and how I might tell the difference on a bare screen?
|
|
|
|
|
Logged
|
|
|
|
|
peteracs
|
|
« Reply #1 on: June 11, 2014, 01:28:49 PM » |
|
Hi Stuart
Did not realise there were any UK unbonded versions on Spider, I thought it came in after they had finished?
The difference will be in the p/n, but I had both next to each other and there is just a centimetre or so difference in the size, so I would measure them to make sure.
Peter
|
|
|
|
« Last Edit: June 11, 2014, 09:59:11 PM by peteracs »
|
Logged
|
Beta Spyder S2 pre F/L 1600
Beta HPE S2 pre F/L 1600
|
|
|
|
lukasdeopalenica
|
|
« Reply #2 on: June 11, 2014, 03:58:54 PM » |
|
They definitely differ in height. As far as I know the bonded windscreen, at least in coupes and HPEs is ca 1cm higher than the rubber seal mounted (68,5cm)
|
|
|
|
|
Logged
|
Lancia Beta HPE 2000i.e. '82 rosso corsa
SAAB 900i 16V Aero, '93 solid black
Subaru Outback 3.0R
Honda CB125 K6 '76 electric blue
Specialized Epic & Stumpjumper
|
|
|
|
Neil-yaj396
|
|
« Reply #3 on: June 11, 2014, 07:21:11 PM » |
|
Hi Stuart
Did not realise there were any UK unbounded versions on Spider, I thought it cam in after they had finished?
The difference will be in the p/n, but I had both next to each other and there is just a centimetre or so difference in the size, so I would measure them to make sure.
Peter
Also thought only the VX and ie models had the unbonded screen in the UK. |
|
|
|
|
Logged
|
|
|
|
|
rossocorsa
|
|
« Reply #4 on: June 11, 2014, 08:51:39 PM » |
|
Will try to check the microfiche when I have time, not convinced that lancia would have fitted the rubber seal type to spiders as the bonded screen will assist rigidity never actually tried it but I was under the impression that the screens are interchangeable in that you could fit a screen with rubber to a bonded screen car(??) anyone know for certain?
|
|
|
|
|
Logged
|
|
|
|
|
peteracs
|
|
« Reply #5 on: June 11, 2014, 09:58:27 PM » |
|
Will try to check the microfiche when I have time, not convinced that lancia would have fitted the rubber seal type to spiders as the bonded screen will assist rigidity never actually tried it but I was under the impression that the screens are interchangeable in that you could fit a screen with rubber to a bonded screen car(??) anyone know for certain?
I can confirm they are different sizes and hence would not be able to fit the later one to a bonded screen. Peter |
|
|
|
|
Logged
|
Beta Spyder S2 pre F/L 1600
Beta HPE S2 pre F/L 1600
|
|
|
|
rossocorsa
|
|
« Reply #6 on: June 11, 2014, 10:54:02 PM » |
|
I thought the aperture was the same and the sealing method dictated the difference in screen size as the rubber seal is thicker ??
|
|
|
|
|
Logged
|
|
|
|
|
lukasdeopalenica
|
|
« Reply #7 on: June 12, 2014, 07:37:25 AM » |
|
That is the point.
|
|
|
|
|
Logged
|
Lancia Beta HPE 2000i.e. '82 rosso corsa
SAAB 900i 16V Aero, '93 solid black
Subaru Outback 3.0R
Honda CB125 K6 '76 electric blue
Specialized Epic & Stumpjumper
|
|
|
|
|
|
HFStuart
|
|
« Reply #9 on: June 12, 2014, 08:52:11 AM » |
|
Much appreciated
|
|
|
|
|
Logged
|
|
|
|
|
peteracs
|
|
« Reply #10 on: June 12, 2014, 10:08:11 AM » |
|
Following on from your comment in this thread what is the size of the fiches? Peter |
|
|
|
|
Logged
|
Beta Spyder S2 pre F/L 1600
Beta HPE S2 pre F/L 1600
|
|
|
|
rossocorsa
|
|
« Reply #11 on: June 27, 2014, 08:08:28 AM » |
|
240mm x 180mm
apologies for slow reply been rather busy! I can check this again but last time I enquired only the normal smaller format fiche could be done
|
|
|
|
|
Logged
|
|
|
|
|
spud
|
|
« Reply #12 on: June 27, 2014, 01:02:45 PM » |
|
Also thought only the VX and ie models had the unbonded screen in the UK. My VX has a bonded screen from new. Andrew. |
|
|
|
|
Logged
|
Montecarlo S2 Spyder
HPE VX
Y10 GTi.e. x2
Various other non Lancia projects...
|
|
|
|
